Temperature dependence of turn-on time delay of semiconductor laser diode: Theoretical analysis

Temperature dependence of the turn-on time delay (t_on) of uncooled semiconductor laser diodes biased below and above threshold is analyzed in presence of data pattern effect. We show that even when the laser is biased at or slightly above threshold, the increase in temperature of operation will lead to increase in the threshold carrier (N_th) and consequently the laser diode will be biased below the threshold again and a significant value of t_on will be produced. Thus, knowledge about a value of dc-bias current required to achieve zero t_on within wide range of temperature degrees is important when considering uncooled laser diode in high-speed optical communication systems. The temperature dependence of t_on is calculated according to the temperature dependence of N_th and Auger recombination coefficient (C) and not by the well-know exponentional relationship of threshold current with temperature. The temperature dependence of N_th is calculated according to the temperature dependence of laser cavity parameters. Advanced analytical model is derived in term of carrier density, recombination coefficients and the injection current (I_inj). The validity of proposed model is confirmed by a numerical method. In addition, approximated models are included where under specified assumptions the proposed model reduces to the well-known approximate models of t_on. According to our typical values and at a specified value of modulation current, the dc-bias one (I_ib) should be increased from I_ib = I_th to I_ib ≈ 1.25 and 1.5I_th in order to achieve approximately zero t_on when the temperature increases from 25°C to 55°C and 85°C, respectively.     

Residual determination and risk assessment of buprofezin in plum (Prunus domestica) grown in open‐field conditions following the application of three different formulations

This study was conducted to characterize the residual level and perform a risk assessment on buprofezin formulated as an emulsifiable concentrate, wettable powder, and suspension concentrate over various treatment schedules in plum (Prunus domestica). The samples were extracted with an AOAC quick, easy, cheap, effective, rugged, and safe, ‘QuEChERS’, method after major modifications. As intrinsic interferences were observed in blank plum samples following dispersive‐solid phase extraction (consisting of primary secondary amine and C₁₈ sorbents), amino cartridges were used for solid‐phase extraction. Analysis was carried out using liquid chromatography with diode array detection and confirmed by liquid chromatography–tandem mass spectrometry. The method showed excellent linearity with determination coefficient (R² = 1) and satisfactory recoveries (at two spiking levels, 0.5 and 2.5 mg/kg) between 90.98 and 94.74% with relative standard deviation (RSD) ≤8%. The limit of quantification (0.05 mg/kg) was considerably lower than the maximum residue limit (2 mg/kg) set by the Codex Alimentarius. Absolute residue levels for emulsifiable concentrates were highest, perhaps owing to the dilution rate and adjuvant. Notably, all formulation residues were lower than the maximum residue limit, and safety data proved that the fruits are safe for consumers. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and characterization of conducting polyaniline layered magnetic nano composite polymer particles

Considering the application potentials of organic materials possessing both conducting and ferromagnetic functions in various electronic devices, an attempt was made to prepare conducting polyaniline (PANI) layered magnetic nano composite polymer particles. Two routes were used to modify magnetic Fe₃O₄ core particles. In one route, seeded emulsion polymerization of methyl methacrylate (MMA) was carried out in presence of nano‐sized Fe₃O₄ core particles. In another route, cross‐linker ethyleneglycol dimethacrylate (EGDM) was used in addition to MMA. The modified composite particles were named as Fe₃O₄/PMMA and Fe₃O₄/P(MMA‐EGDM), respectively. Finally, seeded chemical oxidative polymerization of aniline was carried out in the presence of Fe₃O₄/PMMA and Fe₃O₄/P(MMA‐EGDM) composite seed particles to obtain Fe₃O₄/PMMA/PANI and Fe₃O₄/P(MMA‐EGDM)/PANI composite polymer particles. The modification of Fe₃O₄ core particles was confirmed by electron micrographs, FTIR, UV–visible spectra, X‐ray photoelectron spectra, X‐ray diffraction pattern and thermogravimetric analyses. A comparative study showed that crosslinking of intermediate shell improved the magnetic susceptibility and electrical conductivity of PANI layered magnetic nano composite particles. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis,Electrical Conductivity,Spectral and Thermal Stability Studies on Poly(aniline-co-o-nitroaniline)

o-Nitroaniline units were incorporated in the polyaniline backbone through copolymerization with aniline. The copolymers were synthesized for 1:3 and 1:1 molar ratios of aniline and o-nitroaniline in acidic medium using potassium persulphate as oxidant and their properties were compared with that of polyaniline. The polymers showed less electrical conductivity than polyaniline. Unlike polyaniline, the presence of nitro group caused higher frequency dependence of electrical conductivity. Electronic spectra showed a blue shift in both the band of the copolymers due to the decrease in the extent of conjugation leading to lower conductivity, which could also be explained in terms of a decrease of delocalization of electron as evinced from electron para magnetic resonance (EPR) data. Thermo gravimetric analysis (TGA) revealed that copolymer derived from 1:1 molar ratio showed comparable thermal stability with polyaniline and the one derived from 1:3 molar ratios is thermally less stable than polyaniline. Activation energies for thermal degradation were estimated using Broido equation. The temperature dependence of electrical conductivity suggested charge transport is mainly through variable range hopping.     

Aromatic Polynitro Ether Derivatives of Cellulose

The nucleophilic reaction of sodium cellulosate in the form of membrane or cotton fabric with 2, 4-dinitrohalo-benzenes, 2, 4, 6-trinitrochlorobenzene, 2, 4, 6-trinitrobenzyl bromide, and 2, 4, 6-trinitrostyrene was investigated. The degree of substitution attained with the dinitroaryl derivatives was much higher than that with the trinitroaryl derivatives. The reaction proceeded through Meisen-heimer complexes, which in the case of the trinitro derivatives could be isolated. The ability of the polynitro phenyl ether derivatives of the cellulose to form n- and π-complexes was investigated using naphthalene and p-toluidine. No -π- complex was formed with the former, and the latter gave complexes only with the 2, 4, 6-trinitrobenzyl or -phenethyl cellulose derivatives but not with the trinitrophenyl. The results were explained as due to steric hindrance from the polymeric cellulosic backbone.     

Synthesis,Electrical, Electronic and Charge Transport Properties of Poly(aniline‐co‐p‐toluidine)

Copolymers of aniline with p‐toluidine were synthesized for different molar ratios of the respective monomers in acid medium. The electrical conductivity, charge transport and spectral characteristics upon incorporation of p‐toluidine units into the polyaniline backbone were investigated. The electrical conductivity of the copolymers showed frequency dependence which became more prominent with an increase in the number of p‐toluidine units in the polyaniline backbone. A direct relationship between the frequency dependence and electron localization was observed in the copolymers. Electronic spectra showed blue shifts in the π→π*and benzenoid→quinoid transitions revealing a decrease in the extent of conjugation in the copolymers. The protonated forms of the copolymers were soluble in DMSO giving polaron band around 400 nm. The decrease in electrical conductivity was attributed to the greater electron localizations as revealed from the broader ESR signals. Temperature dependence of electrical conductivity showed that charge transport was mainly through variable range hopping though a mixed conduction behavior was observed at higher temperature range.     

Molecular imprinted polymers for separation science: A review of reviews

Molecular imprinted polymer is an artificial receptor made by imprinting molecules of a template in a polymer matrix followed by removing the template molecules via thorough washing to give the permanent template grooves. They show favored affinity to the template molecule compared to other molecules, and this property is the basic driving force for such diverse application of this techniques. Such techniques have been increasingly employed in a wide scope of applications such as chromatography, sample pretreatment, purification, catalysts, sensors, and drug delivery, etc., mostly in bioanalytical areas. A major part of them is related to development of new stationary phases and their application in chromatography and sample pretreatment. Embodiments of molecular imprinted polymer materials have been carried out in a variety of forms such as irregularly ground particles, regular spherical particles, nanoparticles, monoliths in a stainless steel or capillary column, open tubular layers in capillaries, surface attached thin layers, membranes, and composites, etc. There have been numerous review articles on molecular imprinted polymer issues. In this special review, the reviews in recent ca. 10 years will be categorized into several subgroups according to specified topics in separation science, and each review in each subgroup will be introduced in the order of date with brief summaries and comments on new developments and different scopes of prospects. Brief summaries of each categories and conclusive future perspectives are also given.     

Determination of phthalate esters in bottled water using dispersive liquid–liquid microextraction coupled with GC–MS

Dispersive liquid–liquid microextraction method was developed for the determination of the amount of phthalate esters in bottled drinking water samples and dispersive liquid–liquid microextraction samples were analyzed by GC–MS. Various experimental conditions influencing the extraction were optimized. Under the optimized conditions, very good linearity was observed for all analytes in a range between 0.05 and 150 μg/L with coefficient of determination (R²) between 0.995 and 0.999. The LODs based on S/N = 3 were 0.005–0.22 μg/L. The reproducibility of dispersive liquid–liquid microextraction was evaluated. The RSDs were 1.3–5.2% (n = 3). The concentrations of phthalates were determined in bottled samples available in half shell. To understand the leaching profile of these phthalates from bottled water, bottles were exposed to direct sunlight during summer (temperature from 34–57°C) and sampled at different intervals. Result showed that the proposed dispersive liquid–liquid microextraction is suitable for rapid determination of phthalates in bottled water and di‐n‐butyl, butyl benzyl, and bis‐2‐ethylhexyl phthalate compounds leaching from bottles up to 36 h. Thereafter, degradation of phthalates was observed.